You use family inet to assign an IPv4 address. You use family inet6 to assign an IPv6 address. An interface can be configured with both an IPv4 and IPv6 address.

What is family INET in Juniper?

You use family inet to assign an IPv4 address. You use family inet6 to assign an IPv6 address. An interface can be configured with both an IPv4 and IPv6 address.

How do I set an interface IP in Juniper?

To configure a management port by CLI commands.

  1. Use the command “family inet address” to configure a management IP address on the interface.
  2. Configure a static route with the next hop to the management network default gateway set routing-options static route 0.0.0.0/0 next-hop 10.93.15.1/21.

What is VME interface?

VMEbus (Versa Module Europa or Versa Module Eurocard bus) is a computer bus standard, originally developed for the Motorola 68000 line of CPUs, but later widely used for many applications and standardized by the IEC as ANSI/IEEE 1014-1987.

What is me0 in Juniper?

The Juniper Networks Junos operating system (Junos OS) for EX Series switches automatically creates the switch’s management Ethernet interface, me0. The management Ethernet interface provides an out-of-band method for connecting to the switch. To use me0 as a management port, you must configure its logical port, me0.

What is protocol family?

A protocol family is a group of logical properties within an interface configuration. Protocol families include all the protocols that make up a protocol suite. To use a protocol within a particular suite, you must configure the entire protocol family as a logical property for an interface.

How do you create a subinterface in Juniper SRX?

To configure the subinterfaces on the access switch:

  1. On the trunk interface of the access switch, enable VLAN tagging:
  2. Bind vlan1’s VLAN ID to the logical interface:
  3. Set vlan1’s subinterface IP address:
  4. Bind vlan2’s VLAN ID to the logical interface:
  5. Set vlan2’s subinterface IP address:

How do I find my interface configuration in Juniper?

To display the current configuration for a Juniper Networks device, use the show command in configuration mode. This command displays the configuration at the current hierarchy level or at the specified level.

How do I enable interface in Juniper?

Enable/Disable Interface in Juniper

  1. root@Juniper# set interfaces ge-0/0/1.0 disable << This is cisco equivalent of “shutdown” – To Juniper enable interface:
  2. root@Juniper# delete interfaces ge-0/0/1.0 disable << This is cisco equivalent of “no shutdown” Verification:
  3. root@Juniper#show ge-0/0/1.0.

What is VME and VPX?

While VME was based on a bus, with signals daisy-chained at each slot, VPX is based on switched fabrics. One way to think of the bus is like a tollbooth. When there’s just one manned tollbooth, all of the cars in line have to wait for the ones in front of them to finish their transaction before they can go.

What is VXI interface?

VXI defines additional bus lines for timing and triggering as well as mechanical requirements and standard protocols for configuration, message-based communication, multi-chassis extension, and other features.

How do I check my Juniper interface status?

Use the show interfaces command to view the interface speeds. (Optional) Display the specified level of output. (Optional) Display interface description strings. (Optional) Display media-specific information about network interfaces.

How many IP addresses can be configured on a given interface?

An interface can have one primary IP address and multiple secondary IP addresses. Packets generated by the Cisco IOS software always use the primary IP address. Therefore, all routers and access servers on a segment should share the same primary network number.

What is the difference between INET and UNIT 0?

In that case unit 0 often refers to the untagged interface. family inet refers to the IPv4 address family. An interface can have configuration for multiple address families, each with their own specific configuration and purpose. Thanks for contributing an answer to Network Engineering Stack Exchange!

What is the INET address family?

family inet refers to the IPv4 address family. An interface can have configuration for multiple address families, each with their own specific configuration and purpose. Thanks for contributing an answer to Network Engineering Stack Exchange!

How do I use mE0 as a management port on a switch?

To use me0 as a management port, you must configure its logical port, me0.0, with a valid IP address. You can connect to the management interface over the network using utilities such as ssh and telnet. Simple Network Management Protocol (SNMP) can use the management interface to gather statistics from the switch.

What is the difference between the mE0 and em0 interfaces?

The me0 interface is typically an RJ-45 port on the Routing Engine. The vme interface is used when the device is part of a Virtual Chassis (VC), and is accessed via the me0 port. For consistency you can configure and use the vme interface on a stand alone switch. The em0 interface is typically an RJ-45 port on the Routing Engine.