Who makes Tuff Torq?
Is Tuff Torq K66 serviceable?
Table of Contents
Who makes Tuff Torq?
Yanmar Global
Tuff Torq Corporation is part of the Yanmar Global family of companies and draws upon their decades of experience to develop the premium product lines to best support our customers.
Where is Tuff Torq located?
Morristown, Tennessee
Tuff Torq Corporation is based in Morristown, Tennessee and handles all manufacturing functions for products within U.S. facilities.
Is Tuff Torq K66 serviceable?
The Tuff Torq Professional Series IHT’s are, K62, K66, K72, K92. They are described as for use in Commercial applications and are designed for “Heavy Usage”, ie, “Ground Engagement” and “Serviceable”, they also have heavier 1″ plus axles.
Is the Tuff Torq K46 a good transmission?
The Tuff Torq K46 is the most popular integrated hydrostatic transaxle (IHT) in the world…and for good reason. This power unit has all the features and performance of much larger and more expensive transaxles, all at a very affordable cost and in a small and purpose-focused design.
What is Tuff Torq?
Tuff Torq manufactures transmissions and transaxles for the Lawn and Garden power equipment industry. We are located in the Morristown, Tennessee on the rim of the Smoky Mountains. Tuff Torq has over 100,000 square feet of manufacturing space.
How much oil does a k46 transaxle hold?
approximately 2.2 liters
Tuff Torq recommends using only using approved Tuff Tech drive fluid when servicing any of our transaxles. Only use the fill port (covered by the black cap) to refill unit. You will need approximately 2.2 liters of oil to properly refill the unit if completely empty.
What kind of oil does a Tuff Torq transaxle take?
Tuff Tech drive fluid
Tuff Torq recommends using only using approved Tuff Tech drive fluid when servicing any of our transaxles.
How do you add oil to a Tuff Torq Transmission?
After placing the transaxle on a bench surface remove the fan & pulley and pry open the black cap and remove magnet (see Fig #1). Invert transaxle to allow the oil to drain from case through the port under the black cap. Refill transmission case with oil through same port to near top of the case.
Is the K46 transmission serviceable?
Normally the Residential IHT (K46), which is featured in many tractor & rider models, does not require any servicing for the life of the vehicle. However, if there is a desire to check or replace oil, it may be necessary to remove the transaxle from the vehicle to access the black cap located under the pulley and fan.
How much oil does a K46 transaxle hold?
How much oil does a Tuff Torq K46?
You will need approximately 2.2 liters of oil to properly refill the unit if completely empty. The amount of oil needed may vary for your service, due to the amount of residual oil remaining in case after draining and the condition/age of the unit you are servicing.
How to contact tuff Torq aftermarket services?
A B Tuff Torq Aftermarket Services 6041 Hunter Road Talbott TN 37877 Telephone 1-866-572-3441 Email: [email protected] level to FILL LINE usually embossed on side of plastic tank. Finally top off gear chamber and reinstall both caps. If vehicle is equipped with a K62 the transaxle will need to be purged of air before using.
How do I purge my K62 transaxle?
If vehicle is equipped with a K62 the transaxle will need to be purged of air before using. Follow purging guide attached. The K66 equipped with charge pump will self-purge during initial strokes of the control pedal/fender lever. Page #2 Fig. #2 Oil Fill Locations on Top Side of K62/K66 Case. Gear Chamber Hydro Chamber
What is a K62 transmission?
The K62 is not just an upgraded version of our popular Residential series of transaxles. These drive systems have been engineered from the ground up for the demands of heavier and more function-rich mower and tractor applications.
How do you fill the line on a K66 transmission?
level to FILL LINE usually embossed on side of plastic tank. Finally top off gear chamber and reinstall both caps. If vehicle is equipped with a K62 the transaxle will need to be purged of air before using. Follow purging guide attached. The K66 equipped with charge pump will self-purge during initial strokes of the control pedal/fender lever.